Announcement systems since 1975 · Canada & United States
Downloads
INTERALIA Audio Systems
ATISSBX2SBX3XMU+iProMOH-V5SAMiMCMSupportAboutContact
Contact us
Products / XMU+
Fully supported Expandable ATIS & announcement platform

XMU+

The expandable, multitasking member of the family. A card-cage chassis that grows with line cards — up to 64 analog ports, six hours of audio and 999 messages per partition — with redundant, hot-swappable power for sites that cannot go quiet.

Configured for ATIS, it feeds control-tower transmitters with push-to-talk and ring-down access. Configured for telecom, it runs auto attendant, call-centre queue, dial-by-name and music-on-hold for a building’s PBX. Both are administered with XMUCOM+.

Request a quote XMU+ brochure (PDF)
XMU+ large chassis, front
System diagram: XMUCOM+ on the LAN administers XMU+ and SBX2 announcers, which feed audio to a radio transmitter or a phone system music-on-hold input XMU+ cards: part 47930 hot-swap AC power supply and part 47374 XMU+ ATIS line card XMU+ accessory kit: power cord, Ethernet cable, handset, large rack-mount brackets, 8 screws and rubber feet
8–64 analog ports, by line card
6 hr maximum recording time
999 messages per partition
64 partitions
2 × PSU redundant, hot-swap, AC or DC
Capabilities

One chassis, sized to the job.

Grows with line cards

Start small and add hybrid analog, T1 or music-on-hold cards as the site grows — from a handful of ports to 64 analog, 48 T1 or 32 MOH outputs in one chassis.

Built for the tower

The ATIS configuration drives 4–32 transmitter outputs with push-to-talk relay contacts, and adds a ring-down circuit and front-panel handset for recording at the rack.

No gap in the broadcast

Record the next cycle while the current one plays. Time-sensitive messages such as weather can be flagged so outdated audio is never restored to air.

Redundant by design

Dual hot-swappable power supplies, AC or −48 VDC, for continuous uptime. Messages and configuration are retained through a power failure.

Call processing for the PBX

Auto attendant, ACD front-end, dial-by-name, in-queue messaging and music-on-hold. Offload the voice mail system, or give the PBX overflow and failover.

Manage a fleet remotely

XMUCOM+ configures over the network, by modem or by dial-in, and manages up to 1,000 XMU+ units. Front-panel programming covers the rest.

Line cards

Pick the cards, build the system.

Every XMU+ starts with the chassis, control card and power. The line cards decide what it connects to.

Air traffic

ATIS configuration

Hot-swappable ATIS control card with ring-down daughter board ATIS line card for transmitter feeds 4–32 Tx outputs · 8–64 phone-in ports Push-to-talk relay contacts
Analog

Hybrid line card

8 ports on a female RJ21X connector Loop or ground start ring detection E&M signalling and continuous play Up to 8 cards per chassis
Digital

T1 line card

24 ports per card, RJ-45, 100 Ω SF/D4 and ESF framing · AMI and B8ZS Loop start signalling, hookflash transfer 2 cards in the large chassis (48 ports)
On hold

Music-on-hold card

2 inputs and 4 outputs per card 8 Ω or 600 Ω, −15 to +9 dB 4–32 MOH ports per chassis Up to 8 cards per chassis
Specifications

The whole sheet, on the page.

No gated PDF between you and the numbers you need to size an install.

Capacity and interfaces
Analog portsup to 64
T1 portsup to 48
ATIS transmitter outputs4–32
Front-panel handset220 Ω
Remote phone accessRJ-11
CommunicationsRJ-45 TCP/IP · RS-232 · modem
Alarm contacts2 out · 1 in
Audio
Recording capacity8 minutes to 6 hours
Messages999 per partition · 64 partitions
File format.wav, mono
Encoding8-bit CCITT µ-Law PCM
Sampling rate8 kHz
Frequency response200 Hz – 3.4 kHz
StorageSDRAM and Flash
Power and physical
AC supply110/240 VAC, 1.0/0.5 A, 60/50 Hz
DC supply−48 VDC, 2.5 A
Consumption120 W
Power suppliesDual, redundant, hot-swap
Dimensions, large chassis (H × W × D)7 × 17.5 × 12 in
Mounting19″ rack, card cage
Software and compliance
ConfigurationXMUCOM+ v8.00.09
Audio editingMessage Manager v2.00.01 (optional)
Current firmwarev6.86.19
Remote managementup to 1,000 units
SecurityFTP security · socket connections
CertificationFCC · CS-03 · CSA/US · CE · A-Tick

Need fewer ports in one rack unit? The SBX2 covers eight ports in 1U. Planning a new install for the long term? See the SBX3 preview →

What’s in the box

Everything to rack it and run it.

Every XMU+ ships with an accessory kit, so it can go straight into the rack and onto the network.

Power cordAC line cord
Ethernet cablePatch cord for the LAN connection
HandsetFor recording and checking messages at the unit
Rack-mount bracketsPair of steel rack-mount brackets
Bracket screws8 screws to fit the brackets
Rubber feet4 self-adhesive feet for shelf or desktop use

The XMU+ kit includes the large brackets made for the XMU+ chassis.

XMU+ accessory kit: power cord, Ethernet cable, handset, large rack-mount brackets, 8 screws and rubber feet
Ordering

How to buy an XMU+

Every XMU+ is quoted to the site — the chassis, AC or DC power, recording time and the mix of line cards depend on what it connects to. Tell us the application and we will come back with a part list.

Request a quote Find a reseller

Already running an XMU+? Line cards, spares and repairs are still available — see support.

Documents for this product
PDF
PDF
PDF
PDF
PDF
PDF
PDF
PDF
PDF
XMUCOM+ v8.00.09 · Message Manager v2.00.01
Software
XMU+ firmware v6.86.19
Download
INTERALIA

Announcement and messaging hardware, designed and built in Canada since 1975.

ATIS XMU+ ATISSBX2 ATISSBX3 previewComparison sheet
Products iProMOHiMCMSimple Audio MixerDiscontinued
Support ManualsFirmwareXMUCOM+Open a ticket
Contact 7922 Okanagan Landing Rd, Suite 601
Vernon, BC V1H 2K5
4786 1st Ave South, Suite 102
Seattle, WA 98134
1-800-661-9406
© 2026 Interalia Inc. Privacy · Terms & Conditions · Software EULA · Music licensing notice